Source

StarDSP / doc / sout3 / annexe_surf.md

Full commit

\appendix

Surface de contrôle

\begin{figure}[h] \centering \includegraphics[scale=0.50]{../img/surface.jpg} \caption{La surface de contrôle} \end{figure}

\begin{figure}[h] \centering \includegraphics[scale=0.8]{../img/pinout.png} \caption{Atmega 8515} \label{pin8515} \end{figure}

\begin{figure}[!h] \centering \includegraphics[scale=0.50]{../img/STK500.jpg} \caption{STK500} \end{figure}

\begin{figure}[h] \centering \includegraphics[width=\linewidth]{../img/atmega1280.png} \caption{Atmega 1280} \label{pin1280} \end{figure}

\begin{figure}[h] \centering \includegraphics[scale=0.6]{../img/dfrduino.png} \caption{DFRduino Mega} \end{figure}

\begin{figure}[h] \centering \includegraphics[width=200px]{../img/ft232.png} \caption{FT232RL} \label{pinft232} \end{figure}

\begin{figure}[h] \centering \includegraphics[scale=0.8]{../img/icsp.jpg} \caption{Programmation de l'Atmega 1280 par ICSP} \end{figure}

\begin{figure}[h] \centering \includegraphics[scale=0.7]{../img/cksel.png} \caption{Configuration de la source d'horloge grâce aux fusibles — \emph{fuses}} \label{fuses} \end{figure}

\begin{figure}[h] \centering \includegraphics{../img/clock_osc.png} \caption{Low power crystal oscillator} \label{lpco} \end{figure}

\begin{figure}[h] \centering \includegraphics{../img/clock_ext.png} \caption{External clock} \label{clockext} \end{figure}

\begin{figure}[h] \centering \includegraphics[width=\linewidth]{../img/crystal_1280.png} \caption{Circuit d'horloge du DFRduino Mega} \label{clockduino} \end{figure}

\begin{figure}[!h] \centering \includegraphics[width=\linewidth]{../img/osc_sel.png} \caption{Sélection du signal d'horloge sur STK500} \label{jumpers} \end{figure}

\begin{figure}[!h] \centering \includegraphics[width=\linewidth]{../img/osc_stk500.png} \caption{Les différentes sources d'horloge du STK500} \label{clocksrc} \end{figure}

\begin{figure}[!h] \centering \includegraphics[scale=0.6]{../img/clock.jpg} \caption{Cadencer l'Atmega 1280 avec un signal d'horloge externe} \label{contact} \end{figure}

\begin{figure}[!h] \centering \includegraphics[scale=0.50]{../img/uart.png} \caption{Fonctionnement de l'UART} \end{figure}

\begin{figure}[!h] \centering \includegraphics[scale=0.50]{../img/frame_format.png} \caption{Format de trame} \end{figure}

\begin{figure}[!h] \centering \includegraphics[scale=0.45]{../img/can.png} \caption{Fonctionnement du CAN} \label{can} \end{figure}

\begin{figure}[h] \centering \includegraphics[scale=0.5]{../img/leds.jpg} \caption{Visualisateur du signal sonore} \label{leds} \end{figure}