+U-Boot 2010.06 (Aug 30 2017 - 16:48:06)
+Check Flash Memory Controller v100 ... Found
+SPI Nor(cs 0) ID: 0xef 0x40 0x17
+spi_general_qe_enable(300): Error: Disable Quad failed! reg: 0x2
+Block:64KB Chip:8MB Name:"W25Q64FV"
+Cannot found a valid SPI Nand Device
+EMMC/MMC/SD controller initialization.
+Card did not respond to voltage select!
+No EMMC/MMC/SD device found !
+Hit any key to stop autoboot: 0
+8192 KiB hi_fmc at 0:0 is now current device
+## Booting kernel from Legacy Image at 82000000 ...
+ Image Name: Linux-3.4.35
+ Image Type: ARM Linux Kernel Image (uncompressed)
+ Data Size: 2069296 Bytes = 2 MiB
+ Loading Kernel Image ... OK
+Uncompressing Linux... done, booting the kernel.
+Booting Linux on physical CPU 0
+Linux version 3.4.35 (root@ubuntu) (gcc version 4.8.3 20131202 (prerelease) (Hisilicon_v300) ) #61 Wed Aug 30 18:45:19 CST 2017
+CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
+CPU: VIVT data cache, VIVT instruction cache
+Memory policy: ECC disabled, Data cache writeback
+Built 1 zonelists in Zone order, mobility grouping on. Total pages: 7112
+Kernel command line: mem=28M console=ttyAMA0,115200 root=/dev/mtdblock2 rootfstype=squashfs mtdparts=hi_sfc:384k(boot),2048k(kernel),2560k(rootfs),320k(rom),-(app)
+PID hash table entries: 128 (order: -3, 512 bytes)
+Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
+Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
+Memory: 28MB = 28MB total
+Memory: 24200k/24200k available, 4472k reserved, 0K highmem
+Virtual kernel memory layout:
+ vector : 0xffff0000 - 0xffff1000 ( 4 kB)
+ fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
+ vmalloc : 0xc2000000 - 0xff000000 ( 976 MB)
+ lowmem : 0xc0000000 - 0xc1c00000 ( 28 MB)
+ modules : 0xbf000000 - 0xc0000000 ( 16 MB)
+ .text : 0xc0008000 - 0xc03a0000 (3680 kB)
+ .init : 0xc03a0000 - 0xc03bcfc4 ( 116 kB)
+ .data : 0xc03be000 - 0xc03e46e0 ( 154 kB)
+ .bss : 0xc03e4704 - 0xc0413c98 ( 190 kB)
+SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
+VIC @fe0d0000: id 0x00641190, vendor 0x41
+sched_clock: 32 bits at 49MHz, resolution 20ns, wraps every 86767ms
+Console: colour dummy device 80x30
+Calibrating delay loop... 269.10 BogoMIPS (lpj=1345536)
+pid_max: default: 32768 minimum: 301
+Mount-cache hash table entries: 512
+Initializing cgroup subsys freezer
+CPU: Testing write buffer coherency: ok
+Setting up static identity map for 0x802b9a88 - 0x802b9ae0
+NET: Registered protocol family 16
+Serial: AMBA PL011 UART driver
+uart:0: ttyAMA0 at MMIO 0x20080000 (irq = 5) is a PL011 rev2
+console [ttyAMA0] enabled
+uart:1: ttyAMA1 at MMIO 0x20090000 (irq = 30) is a PL011 rev2
+uart:2: ttyAMA2 at MMIO 0x200a0000 (irq = 25) is a PL011 rev2
+bio: create slab <bio-0> at 0
+SCSI subsystem initialized
+hi-spi-master hi-spi-master.0: with 1 chip select slaves attached
+hi-spi-master hi-spi-master.1: with 2 chip select slaves attached
+usbcore: registered new interface driver usbfs
+usbcore: registered new interface driver hub
+usbcore: registered new device driver usb
+Switching to clocksource timer0
+NET: Registered protocol family 2
+IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
+TCP established hash table entries: 1024 (order: 1, 8192 bytes)
+TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
+TCP: Hash tables configured (established 1024 bind 1024)
+UDP hash table entries: 256 (order: 0, 4096 bytes)
+UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
+NET: Registered protocol family 1
+squashfs: version 4.0 (2009/01/31) Phillip Lougher
+jffs2: version 2.2. (NAND) c 2001-2006 Red Hat, Inc.
+msgmni has been set to 47
+Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
+io scheduler noop registered
+io scheduler deadline registered (default)
+io scheduler cfq registered
+Check Flash Memory Controller v100 ... Found.
+SPI Nor(cs 0) ID: 0xef 0x40 0x17
+spi_general_qe_enable(292): Error: Disable Quad failed! reg: 0x2
+Block:64KB Chip:8MB Name:"W25Q64FV"
+5 cmdlinepart partitions found on MTD device hi_sfc
+5 cmdlinepart partitions found on MTD device hi_sfc
+Creating 5 MTD partitions on "hi_sfc":
+0x000000000000-0x000000060000 : "boot"
+0x000000060000-0x000000260000 : "kernel"
+0x000000260000-0x0000004e0000 : "rootfs"
+0x0000004e0000-0x000000530000 : "rom"
+0x000000530000-0x000000800000 : "app"
+SPI Nand ID Table Version 2.2
+Cannot found a valid SPI Nand Device
+ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
+hiusb-ehci hiusb-ehci.0: HIUSB EHCI
+hiusb-ehci hiusb-ehci.0: new USB bus registered, assigned bus number 1
+hiusb-ehci hiusb-ehci.0: irq 15, io mem 0x100b0000
+hiusb-ehci hiusb-ehci.0: USB 0.0 started, EHCI 1.00
+hub 1-0:1.0: USB hub found
+hub 1-0:1.0: 1 port detected
+ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
+hiusb-ohci hiusb-ohci.0: HIUSB OHCI
+hiusb-ohci hiusb-ohci.0: new USB bus registered, assigned bus number 2
+hiusb-ohci hiusb-ohci.0: irq 16, io mem 0x100a0000
+hub 2-0:1.0: USB hub found
+hub 2-0:1.0: 1 port detected
+dwc_otg: version 3.00a 10-AUG-2012
+Setting default values for core params
+Periodic Transfer Interrupt Enhancement - disabled
+Multiprocessor Interrupt Enhancement - disabled
+OTG VER PARAM: 0, OTG VER FLAG: 0
+hisi_i2c hisi_i2c.0: Hisilicon [i2c-0] probed!
+hisi_i2c hisi_i2c.1: Hisilicon [i2c-1] probed!
+hisi_i2c hisi_i2c.2: Hisilicon [i2c-2] probed!
+Initializing XFRM netlink socket
+NET: Registered protocol family 17
+NET: Registered protocol family 15
+lib80211: common routines for IEEE802.11 drivers
+Registering the dns_resolver key type
+VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
+Freeing init memory: 112K
+usb 1-1: new high-speed USB device number 2 using hiusb-ehci
+##############################
+##############################
+[RCS]: /etc/init.d/S00devs
+[RCS]: /etc/init.d/S01udev
+[RCS]: /etc/init.d/S80network
+mke2fs 1.41.11 (14-Mar-2010)
+Fragment size=1024 (log=0)
+Stride=0 blocks, Stripe width=0 blocks
+16384 inodes, 65536 blocks
+3276 blocks (5.00%) reserved for the super user
+Maximum filesystem blocks=67108864
+8192 blocks per group, 8192 fragments per group
+Superblock backups stored on blocks:
+ 8193, 24577, 40961, 57345
+Writing inode tables: done
+Writing superblocks and filesystem accounting information: done
+This filesystem will be automatically checked every 31 mounts or
+180 days, whichever comes first. Use tune2fs -c or -i to override.
+Password for root changed by root
+HISI_IRDA-MF @Hi3518v100R001
+hiir: init ok. ver=Jan 3 2007, 19:33:43.
+uart1 init ok. ver=May 24 2007, 18:50:36.
+usbcore: registered new interface driver rtl8188fu
+Hisilicon Watchdog Timer: 0.01 initialized. default_margin=60 sec (nowayout= 0, nodeamon= 0)
++++++++++++++++++++++++++++
+mmz_start: 0x81c00000, mmz_size: 36M
+Hisilicon Media Memory Zone Manager
+hi3518e_base: module license 'Proprietary' taints kernel.
+Disabling lock debugging due to kernel taint
+load sys.ko for Hi3518EV200...OK!
+load vgs.ko for Hi3518EV200...OK!
+load viu.ko for Hi3518EV200...OK!
+load rc.ko for Hi3518EV200...OK!
+load venc.ko for Hi3518EV200...OK!
+load chnl.ko for Hi3518EV200...OK!
+load h264e.ko for Hi3518EV200...OK!
+load jpege.ko for Hi3518EV200...OK!
+load ive.ko for Hi3518EV200...OK!
+==== Your input Sensor type is sc1145 ====
+*** Board tools : ver0.0.1_20121120 ***
+[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
+0x200f006C: 0x00000001 --> 0x00000000
+*** Board tools : ver0.0.1_20121120 ***
+[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
+0x200f0040: 0x00000000 --> 0x00000002
+*** Board tools : ver0.0.1_20121120 ***
+[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
+0x200f0044: 0x00000000 --> 0x00000002
+*** Board tools : ver0.0.1_20121120 ***
+[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
+0x200f007c: 0x00000000 --> 0x00000001
+*** Board tools : ver0.0.1_20121120 ***
+[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
+0x200f0080: 0x00000000 --> 0x00000001
+*** Board tools : ver0.0.1_20121120 ***
+[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
+0x200f0084: 0x00000000 --> 0x00000001
+*** Board tools : ver0.0.1_20121120 ***
+[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
+0x200f0088: 0x00000000 --> 0x00000001
+*** Board tools : ver0.0.1_20121120 ***
+[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
+0x200f008c: 0x00000000 --> 0x00000002
+*** Board tools : ver0.0.1_20121120 ***
+[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
+0x200f0090: 0x00000000 --> 0x00000002
+*** Board tools : ver0.0.1_20121120 ***
+[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
+0x200f0094: 0x00000000 --> 0x00000001
+*** Board tools : ver0.0.1_20121120 ***
+[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
+0x2003002c: 0x000C4003 --> 0x000B4001
+init phy power successful!
+load hi_mipi driver successful!
+==== Your input Sensor type is sc1145 ====
++++++++++++++++++++++++++++
+Jan 1 00:00:09 login[1107]: root login on 'ttyS000'
+# >>>>>>>>>build time:11:20:26<<<<<<<<<<
+insmod: can't insert '/npc/patch/wdt.ko': File exists
+dwNetLed = 0 dwAlarmLed = 0; dwDefenseLed = 0; dwRecLed = 0
+*********vGpioMultipleInit********
+*** Board tools : ver0.0.1_20121120 ***
+[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
+0x200F006C: 0x00000000 --> 0x00000000
+*** Board tools : ver0.0.1_20121120 ***
+[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
+0x200F0100: 0x00000000 --> 0x00000001
+*** Board tools : ver0.0.1_20121120 ***
+[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
+0x200F0104: 0x00000000 --> 0x00000001
+*** Board tools : ver0.0.1_20121120 ***
+[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
+0x200F00F8: 0x00000000 --> 0x00000001
+*** Board tools : ver0.0.1_20121120 ***
+[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
+0x200F00EC: 0x00000000 --> 0x00000001
+*** Board tools : ver0.0.1_20121120 ***
+[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
+0x200F00F0: 0x00000000 --> 0x00000001
+*** Board tools : ver0.0.1_20121120 ***
+[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
+0x200F00F4: 0x00000000 --> 0x00000001
+*** Board tools : ver0.0.1_20121120 ***
+[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
+0x200F00C0: 0x00000000 --> 0x00000003
+*** Board tools : ver0.0.1_20121120 ***
+[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
+0x200F00C8: 0x00000000 --> 0x00000003
+*** Board tools : ver0.0.1_20121120 ***
+[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
+0x200F00CC: 0x00000000 --> 0x00000003
+*** Board tools : ver0.0.1_20121120 ***
+[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
+0x200F00D0: 0x00000000 --> 0x00000003
+*** Board tools : ver0.0.1_20121120 ***
+[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
+0x200F0844: 0x00000090 --> 0x00000080
+*** Board tools : ver0.0.1_20121120 ***
+[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
+0x200F0840: 0x00000040 --> 0x00000000
+*** Board tools : ver0.0.1_20121120 ***
+[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
+0x200F0098: 0x00000001 --> 0x00000000
+*** Board tools : ver0.0.1_20121120 ***
+[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
+0x200F00FC: 0x00000000 --> 0x00000001
+*** Board tools : ver0.0.1_20121120 ***
+[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
+0x200F0004: 0x00000000 --> 0x00000001
+*** Board tools : ver0.0.1_20121120 ***
+[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
+0x200F0068: 0x00000001 --> 0x00000000
+/rom/Certificate.bin exist.
+Certificate: rom file ok, eeprom ok
+info: RTC has been used before, no need to init it
+<1>Sun ??? 0 00:00:00 0000
+<3>Wed Dec 31 23:59:59 1969
+<<<pGetSetting()->bLanguage = 0 >>>>>>>>>>>>SetRtspNewPasswordType(1)on
+p2plib Compile Date: Sep 14 2018 14:54:14
+============fgP2PInit=============
+sChipInfo.dwR1=94987522, sChipInfo.dwR2=120568014
+P2P: ID=17019278, R1=0x5a96502, R2=0x72fb8ce id=0x8f2509ab5d866b
+bDevType=7, bDevSubType=4, 0-0-0
+fgGetCertificateInfo end...
+_convert_init_parm_cfg, devID=17019278, pcfg->devR1=94987522, pcfg->devR2=120568014, devType=7 devSubType=4
+_convert_init_parm_cfg, devID=17019278, pcfg->devR1=94987522, pcfg->devR2=120568014, devType=7, devSubType=4, pcfg->maxChnNum=5
+_convert_init_parm_cfg pcfg->devHelperDisable=0
+CH0: p2pc_chnnel_init success...
+_convert_init_parm_cb &pPrm->fgNoticeVAS=0xbea43c3c pPrm->fgNoticeVAS=0x3e748 &cbfunc->fgNoticeVAS=0x24b5f2c
+DeviceCfgInfoLen=16 bToUploaDevcfgInfoActive=1 dwSoftwareVersion=218169435 bDeviceCfgSendToServerOk=0
+[msg] Nameserver 8.8.8.8:53 has failed: Network is unreachable
+[msg] Nameserver 114.114.114.114:53 has failed: Network is unreachable
+[msg] All nameservers have failed
+*** Board tools : ver0.0.1_20121120 ***
+[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
+0x200F0040: 0x00000002 --> 0x00000002
+*** Board tools : ver0.0.1_20121120 ***
+[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
+0x200F0044: 0x00000002 --> 0x00000002
+[SENSOR_preInit, 1098]sensor level not low
+SaveCmosCtlLevel Level = 1
+in CMOSPowerDown fgLevelCtl = 0
+ [SENSOR_preInit, 1106] : [cmos_type : 16, cmos_resolution : 0, cmos_level : 1][OK]!
+cEmailAddr[0] is 0xffcEmailAddr:
+*************vNetMg_Init******************
++++++++++++++vKey_DrvProc+++++++++++++++
+NIGHT_MODE_STATE INIT...
+dwIrCut_SW_To_NoFilter_Cnt = 50
+vRtspServderThreadStar star!
+[MppSysInit, 3981]encode_mode = 1
+[MPP_getPicSize, 1316] : [width : 1280, height : 720] [OK]!
+MPP_getPicSize success_at MPP_getVbBlkSize: LINE: 1328 !
+[MPP_getPicSize, 1316] : [width : 640, height : 360] [OK]!
+MPP_getPicSize success_at MPP_getVbBlkSize: LINE: 1328 !
+vHandSelectThreadStar star!
+accept ******************
+HI_MPI_VB_SetConf success_at MPP_init: LINE: 2275 !
+HI_MPI_VB_Init success_at MPP_init: LINE: 2276 !
+HI_MPI_SYS_SetConf success_at MPP_init: LINE: 2277 !
+HI_MPI_SYS_Init success_at MPP_init: LINE: 2278 !
+ [MPP_init, 2281]sHiRegCmd.dwBaseAddr = 0x20120000 0xc4
+ : [cmos_type : 16, cmos_sub_type : 4] g_MPP_inisHiRegCmd.dwBaseAddr = 0x20120000 0xc4
+[HI_MPI_AI_SetPubAtsHiRegCmd.dwBaseAddr = 0x20120000 0xc8
+[HI_MPsHiRegCmd.dwBaseAddr = 0x20120000 0xc8
+I_AI_EnableChn](AiChn:0): ok
+[HI_MPI_AI_GetChnParam]: ok
+[HI_MPI_AI_SetChnParam]: ok
+vAudioAmpEn:Need wait 500000us before use Audio[Output] next time..
+ISP xml format check error.
+3DNR xml isn't exist or format error.
+#### read ap wifi password:0000000000000000
+############### first_GarageWhiteLightCtlState :0
+===== Now AT24CXX used 255 Bytes=====
+sHiRegCmd.dwBaseAddr = 0x20650000 0x2004
+@@vNewIrCutHanldeFun to filter, night
+PHY: himii:00 - Link is Up - 10/Half
+mii_val->val_out is 0xFFFF
+***link down status changed***.
+PHY: himii:00 - Link is Down
+fgEth0Support = 0,fgRa0Support = 1
+#### read ap wifi password:0000000000000000
+Configuration file: /etc/Wireless/RTL8188/hostapd.conf
+l2_sock_recv==l2_sock_xmit=0x0xbedc48
++rtl871x_sta_deauth_ops, ff:ff:ff:ff:ff:ff is deauth, reason=2
+Using interface wlan0 with hwaddr 28:ad:3e:46:2a:e3 and ssid 'GW_AP_17019278'
+rtl871x_set_wps_assoc_resp_ie
+rtl871x_set_wps_beacon_ie
+rtl871x_set_wps_probe_resp_ie
+rtl871x_set_hidden_ssid ignore_broadcast_ssid:0, GW_AP_17019278,14
+KEY_AUDIO_OUTPUT_DISABLE
+sHiRegCmd.dwBaseAddr = 0x20650000 0x2004
+udhcpd: bad line 7: 1 tokens found, 2 needed
+udhcpd: bad line 12: 1 tokens found, 2 needed
+udhcpd: bad line 20: 1 tokens found, 2 needed
+udhcpd: bad line 34: 1 tokens found, 2 needed
+udhcpd: bad line 44: 1 tokens found, 2 needed
+udhcpd: bad line 52: 1 tokens found, 2 needed
+udhcpd: bad line 60: 1 tokens found, 2 needed
+udhcpd: bad line 66: 1 tokens found, 2 needed
+udhcpd: bad line 74: 1 tokens found, 2 needed
+udhcpd: bad line 80: 1 tokens found, 2 needed
+udhcpd: bad line 90: 1 tokens found, 2 needed
+udhcpd (v1.20.2) started
+': No such file or directorycpd.leases
+ AP start! udhcpd pid = 1191
+sleep over!dwNowNetSel = 1
+vP2PSetMyPassword... pwdHost=0 pwdGuest=0
+vP2PSetMyPassword... encodepwdHost=836843848 encodepwdGuest=836843848
+KEY_AUDIO_OUTPUT_DISABLE
+sHiRegCmd.dwBaseAddr = 0x20650000 0x2004
+KEY_AUDIO_OUTPUT_DISABLE
+[HI_MPI_AI_SetPubAttr]: ok
+[HI_MPI_sHiRegCmd.dwBaseAddr = 0x20120000 0xc4
+AI_EnableChn](AiChn:0): ok
+[HI_MPI_AI_GsHiRegCmd.dwBaseAddr = 0x20120000 0xc4
+[HI_MPI_AI_SetChnParam]: ok
+sHiRegCmd.dwBaseAddr = 0x20120000 0xc8
+sHiRegCmd.dwBaseAddr = 0x20120000 0xc8
+vAudioAmpEn:Need wait 500000us before use Audio[Output] next time..
+>>emTMFSDKInit InitRet:0
+sHiRegCmd.dwBaseAddr = 0x20650000 0x2004
+KEY_AUDIO_OUTPUT_DISABLE
+sHiRegCmd.dwBaseAddr = 0x20650000 0x2004
+KEY_AUDIO_OUTPUT_DISABLE
+vAudioAmpEn:Need wait 500000us before use Audio[Output] next time..
+sHiRegCmd.dwBaseAddr = 0x20650000 0x2004