Created by 新妻浩光 2018-02-08
snippet.txt


U-Boot 2009.08 (10月 25 2013 - 15:15:40)

CPU:   Freescale i.MX25 at 398 MHz
mx25 cpu clock: 398MHz
ipg clock     : 66498560Hz
Board: i.MX25 - Solar-System JHRWL3 board
I2C:   ready
RAM Configuration:
 Bank #0: 80000000 128 MB
 Bank #1: 90000000 128 MB
SDRAM Test Aread 90000000 - 90100000
SDRAM test phase 1:
SDRAM test phase 2:
SDRAM Test Aread 94000000 - 94100000
SDRAM test phase 1:
SDRAM test phase 2:
SDRAM test passed.
NAND:  Manufacturer      : Micron (0x2c)
Device Code       : 0x38
Cell Technology   : SLC
Chip Size         : 1 GiB
Pages per Block   : 128
Page Geometry     : 4096+218
ECC Strength      : 8 bits
ECC Size          : 512 B
Data Setup Time   : 25 ns
Data Hold Time    : 15 ns
Address Setup Time: 10 ns
GPMI Sample Delay : 6 ns
tREA              : Unknown
tRLOH             : Unknown
tRHOH             : Unknown
Description       : MT29F8G08ABABA
Bad block table found at page 262016, version 0x01
Bad block table found at page 261888, version 0x01
1024 MiB
MMC:
In:    serial
Out:   serial
Err:   serial
Bank 0 - EEPROM Magic Check ....OK(0x9510107)
Bank 0 - EEPROM CRC Verify ....OK
Net:   FEC0
Hit any key to stop autoboot:  0
+++ Barner +++++++++++++++++++++++++++++++++++
 Kernel Image Address : 0x200000
              Version : 11.00
        Build Version : 0001
++++++++++++++++++++++++++++++++++++++++++++++

NAND read: device 0 offset 0x200000, size 0x800000
 8388608 bytes read: OK
## Booting kernel from Legacy Image at 80800000 ...
   Image Name:   Linux-2.6.34.9-WR4.2.0.0_standar
   Created:      2015-10-20   8:18:25 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    6262528 Bytes =  6 MB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.34.9-WR4.2.0.0_standard (solar@solar-server) (gcc version 4.4.1 (Wind River Linux Sourcery G++ 4.4a-333) ) #315 PREEMPT Tue Oct 20 17:18:21 JST 2015
CPU: ARM926EJ-S [41069264] revision 4 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: Sharp MX25 Solar Remote Controller
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 64768
Kernel command line: console=ttymxc0,115200 ubi.mtd=8,1024 root=ubi0:rootfs_a rootfstype=ubifs ro bootcmd=normal
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
allocated 2359296 bytes of page_cgroup
please try 'cgroup_disable=memory,blkio' option if you don't want memory and blkio cgroups
Memory: 128MB 128MB = 256MB total
Memory: 250740k/250740k available, 11404k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xfde00000 - 0xffe00000   (  32 MB)
    vmalloc : 0xd8800000 - 0xf4000000   ( 440 MB)
    lowmem  : 0xc0000000 - 0xd8000000   ( 384 MB)
    modules : 0xbf000000 - 0xc0000000   (  16 MB)
      .init : 0xc0008000 - 0xc0086000   ( 504 kB)
      .text : 0xc0086000 - 0xc05a7000   (5252 kB)
      .data : 0xc05cc000 - 0xc0600f00   ( 212 kB)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
RCU-based detection of stalled CPUs is enabled.
NR_IRQS:208
MXC GPIO hardware
MXC IRQ initialized
Clock input source is 24000000
Console: colour dummy device 80x30
Calibrating delay loop... 198.65 BogoMIPS (lpj=397312)
Security Framework initialized
Mount-cache hash table entries: 512
Initializing cgroup subsys debug
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
Initializing cgroup subsys memory
Initializing cgroup subsys blkio
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
CPU: Testing write buffer coherency: ok
Init trace_clock_cyc2ns: precalc_mult = 250000, precalc_shift = 9
devtmpfs: initialized
regulator: core version 0.5
NET: Registered protocol family 16
AIPS1 VA base: 0xfc000000
CPU is i.MX25 Revision 1.0
mxc_pwm_device registered
pwm-backlight device registered
Using SDMA I.API
MXC DMA API initialized
check_res_of_trace_clock: sched_clock() low resolution
check_res_of_trace_clock: trace_clock_read64_ns() has high resolution
bio: create slab <bio-0> at 0
CSPI: spi_imx-0 probed
MXC I2C driver
cfg80211: Calling CRDA to update world regulatory domain
regulator: REG1_BKLT: 4500 <--> 5500 mV at 5000 mV
regulator: REG2_CPU: 2640 <--> 3877 mV at 3300 mV
regulator: REG3_CORE: 1160 <--> 1703 mV at 1450 mV
regulator: REG4_DDR: 1440 <--> 2115 mV at 1800 mV
regulator: REG5_PERS: 2640 <--> 3877 mV at 3300 mV
mc34704 0-0054: Loaded
Switching to clocksource mxc_timer1
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Bus freq driver module loaded
i.MXC CPU frequency driver
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Registering unionfs 2.5.4 (for 2.6.34-rc0)
JFFS2 version 2.2. (NAND) c 2001-2006 Red Hat, Inc.
fuse init (API version 7.13)
Btrfs loaded
yaffs Oct 20 2015 17:15:19 Installing.
msgmni has been set to 489
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
LTT : ltt-relay init
pwm_backlight_update_status(): bl_power=0 brightness=0
pwm_config(): duty_ns=0 period_ns=5000000
pwm_config(): [MXC_PWMSAR] 00000000
pwm_config(): [MXC_PWMPR ] 0000d878
pwm_config(): [MXC_PWMCR ] 03c20050
pwm_disable(): [MXC_PWMCR ] 03c20050
_update_lcdc : bpp setting 32(default=32) bpp = pcd is 0x3
mxc_sdc_fb mxc_sdc_fb.0: fb0: DISP0 BG fb device registered successfully.
mxc_sdc_fb mxc_sdc_fb.0: fb1: DISP0 FG fb device registered successfully.
ML22823 Power Up
ML22823 Power Down
ML22823 probed
Serial: IMX driver
imx-uart.0: ttymxc0 at MMIO 0x43f90000 (irq = 45) is a IMX
console [ttymxc0] enabled
imx-uart.1: ttymxc1 at MMIO 0x43f94000 (irq = 32) is a IMX
imx-uart.2: ttymxc2 at MMIO 0x5000c000 (irq = 18) is a IMX
brd: module loaded
at24 0-0050: 256 byte 24c02 EEPROM (writable)
MXC MTD nand Driver 2.5
NAND device: Manufacturer ID: 0x2c, Chip ID: 0x38 (Micron NAND 1GiB 3,3V 8-bit)
RedBoot partition parsing not available
Creating 9 MTD partitions on "NAND 1GiB 3,3V 8-bit":
0x000000000000-0x000000080000 : "nand.bootloader0"
0x000000080000-0x000000100000 : "nand.bootloader1"
0x000000100000-0x000000180000 : "nand.bootenv0"
0x000000180000-0x000000200000 : "nand.bootenv1"
0x000000200000-0x000000a00000 : "nand.kernel_a"
0x000000a00000-0x000001200000 : "nand.kernel_b"
0x000001200000-0x000001a00000 : "nand.kernel_c"
0x000001a00000-0x000002200000 : "nand.kernel_d"
0x000002200000-0x000020000000 : "nand.ubi0"
UBI: attaching mtd8 to ubi0
UBI: physical eraseblock size:   524288 bytes (512 KiB)
UBI: logical eraseblock size:    520192 bytes
UBI: smallest flash I/O unit:    4096
UBI: sub-page size:              1024
UBI: VID header offset:          1024 (aligned 1024)
UBI: data offset:                4096
UBI: attached mtd8 to ubi0
UBI: MTD device name:            "nand.ubi0"
UBI: MTD device size:            478 MiB
UBI: number of good PEBs:        956
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     7
UBI: available PEBs:             15
UBI: total number of reserved PEBs: 941
UBI: number of PEBs reserved for bad PEB handling: 9
UBI: max/mean erase counter: 1104/562
UBI: image sequence number: 745870485
UBI: background thread "ubi_bgt0d" started, PID 958
FEC Ethernet Driver
fec_enet_mii_bus: probed
console [netcon0] enabled
netconsole: network logging started
input: gpio-keys as /devices/platform/gpio-keys/input/input0
rtc-pcf8563 0-0051: chip found, driver version 0.4.3
rtc-pcf8563 0-0051: rtc core: registered rtc-pcf8563 as rtc0
i2c i2c-0: ACK not received
rtc-rx8025 0-0032: Unable to read registers #14..#15
i2c i2c-0: probing for rx8025 failed
rtc-rx8025: probe of 0-0032 failed with error -121
i2c /dev entries driver
MXC WatchDog Driver 2.0
MXC Watchdog # 0 Timer: initial timeout 127 sec
PMIC Character device: successfully loaded
i.MX ADC at 0x50030000 irq 46
mxsdhci: MXC Secure Digital Host Controller Interface driver
mxsdhci: MXC SDHCI Controller Driver.
mmc0: SDHCI detect irq 97 irq 9 INTERNAL DMA
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
Static Power Management for Freescale i.MX25
on-off key pressed
regulator_init_complete: incomplete constraints, leaving REG5_PERS on
regulator_init_complete: incomplete constraints, leaving REG1_BKLT on
input: imx_adc_ts as /devices/virtual/input/input1
i.MX ADC input touchscreen loaded.
mmc0: new high speed SDIO card at address 0001
UBIFS: recovery needed
UBIFS: recovery deferred
UBIFS: mounted UBI device 0, volume 1, name "rootfs_a"
UBIFS: mounted read-only
UBIFS: file system size:   104558592 bytes (102108 KiB, 99 MiB, 201 LEBs)
UBIFS: journal size:       10469376 bytes (10224 KiB, 9 MiB, 21 LEBs)
UBIFS: media format:       w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root:  0 bytes (0 KiB)
VFS: Mounted root (ubifs filesystem) readonly on device 0:13.
devtmpfs: mounted
Freeing init memory: 504K
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 3, name "data_a"
UBIFS: file system size:   59301888 bytes (57912 KiB, 56 MiB, 114 LEBs)
UBIFS: journal size:       9883648 bytes (9652 KiB, 9 MiB, 19 LEBs)
UBIFS: media format:       w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root:  0 bytes (0 KiB)
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 4, name "data_b"
UBIFS: file system size:   18206720 bytes (17780 KiB, 17 MiB, 35 LEBs)
UBIFS: journal size:       4681729 bytes (4572 KiB, 4 MiB, 9 LEBs)
UBIFS: media format:       w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root:  0 bytes (0 KiB)
UBIFS: mounted UBI device 0, volume 5, name "config"
UBIFS: mounted read-only
UBIFS: file system size:   18206720 bytes (17780 KiB, 17 MiB, 35 LEBs)
UBIFS: journal size:       4681729 bytes (4572 KiB, 4 MiB, 9 LEBs)
UBIFS: media format:       w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root:  0 bytes (0 KiB)
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 6, name "log"
UBIFS: file system size:   26529792 bytes (25908 KiB, 25 MiB, 51 LEBs)
UBIFS: journal size:       5722112 bytes (5588 KiB, 5 MiB, 11 LEBs)
UBIFS: media format:       w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root:  0 bytes (0 KiB)
BackLight Power On ....
BackLight Max Level 5 ....
pwm_backlight_update_status(): bl_power=0 brightness=255
pwm_enable(): clk_enable
pwm_enable(): [MXC_PWMCR ] 03c20051
pwm_config(): duty_ns=5000000 period_ns=5000000
pwm_config(): [MXC_PWMSAR] 0000d878
pwm_config(): [MXC_PWMPR ] 0000d878
pwm_config(): [MXC_PWMCR ] 03c20051
setting brithness level is 255
error: /etc/logrotate.conf:30 unknown group 'utmp'
error: found error in /var/log/wtmp , skipping
mlan driver install  : mlan: module license 'Marvell Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
[ OK ]
sd8787 driver install  : wlan_sdio mmc0:0001:1: firmware: requesting mrvl/sd8787_uapsta.bin
WLAN FW is active
[ OK ]
console=ttymxc0,115200 ubi.mtd=8,1024 root=ubi0:rootfs_a rootfstype=ubifs ro bootcmd=normal
Copy /backup/ts/pointercal.bak /etc ... Not Found
Copy /data/ts/pointercal /etc ... [ OK ]
+++++++++++++++++++++++++++++++++++
 Last Reset : [ H/W-Reset ]
+++++++++++++++++++++++++++++++++++

---------------------------------------
Version      : 11.00
Build number : 0001
Date         : 2017/05/10 11:44
---------------------------------------

Speech A-Volume Setting
low = 0x26,  mid = 0x2b,  mid_high = 0x31,  high = 0x37
RTC Initialize
2018/02/08 08:32:08
********************
   Mode: [Normal]
********************
START !!!!

JH-RWL7 login: mlan0     deepsleep:0
mlan0     regioncode:65
mlan0     httxcfg:0
mlan0     htcapinfo:67108864
1970-01-01 09:00:14: (log.c.166) server started
1970-01-01 09:00:14: (server.c.968) WARNING: unknown config-key: url.access-deny (ignored)
ioctl[SIOCSIWPMKSA]: Invalid argument
ioctl[SIOCSIWESSID]: Invalid argument
ioctl[SIOCSIWPMKSA]: Invalid argument
pwm_backlight_update_status(): bl_power=0 brightness=255
pwm_enable(): [MXC_PWMCR ] 03c20051
pwm_config(): duty_ns=5000000 period_ns=5000000
pwm_config(): [MXC_PWMSAR] 0000d878
pwm_config(): [MXC_PWMPR ] 0000d878
pwm_config(): [MXC_PWMCR ] 03c20051
udhcpc (v1.15.3) started
Sending discover...
Sending select for 192.168.0.4...
Sending select for 192.168.0.4...
Lease of 192.168.0.4 obtained, lease time 3600
deleting routers
adding dns 192.168.0.1
pwm_backlight_update_status(): bl_power=0 brightness=204
pwm_enable(): [MXC_PWMCR ] 03c20051
pwm_config(): duty_ns=4000000 period_ns=5000000
pwm_config(): [MXC_PWMSAR] 0000ad2c
pwm_config(): [MXC_PWMPR ] 0000d878
pwm_config(): [MXC_PWMCR ] 03c20051
slotCtrlConditionsEvt() 0x2
slotCtrlConditionsEvt() END 0x40
slotCtrlConditionsEvt() 0x40
slotCtrlConditionsEvt() END 0x0
QStateMachine::start(): already running
Comments (28)

HTTPS
SSH
You can clone a snippet to your computer for local editing. Learn more.
Snippets

新妻浩光 SHARP 太陽光発電　エネルギーモニタ JH-RWL7 bootup log

Comments (28)
