Ben Bass  committed f54f3b8

update installation including mention of Raspberry Pi etc

  • Participants
  • Parent commits 67e4b88
  • Branches default

Comments (0)

Files changed (1)

File doc/installation.rst

+There are two steps in getting a sensible installation in Linux systems:
+1. Getting ``libftdi`` and its dependencies installed
+2. Ensuring permissions allow access to the device without requiring root
+   privileges. Symptoms of this not being done are programs only working
+   properly when run with ``sudo``, giving '-4' or '-8' error codes in
+   other cases.
+Each of these steps will be slightly different depending on the distribution
+in use. I've tested ``pylibftdi`` on Debian Wheezy (on a Raspberry Pi),
+Ubuntu (various versions, running on a fairly standard ThinkPad laptop),
+and Arch Linux (running on a PogoPlug - one of the early pink ones).
+Debian (Raspberry Pi) / Ubuntu etc
 On Debian like systems (including Ubuntu, Mint, Debian, etc), the package
 `libftdi-dev` should give you what you need as far as the libftdi library
-is concerned.
+is concerned::
-One potential issue is with permissions to access the device, which can be
-seen as a error when opening devices (with a '-4' or '-8' error code).
-The solution is to add udev rules to deal with the devices - the following
-works for me under Arch linux::
+    $ sudo apt-get install libftdi-dev
-   SUBSYSTEMS=="usb", ATTRS{idVendor}=="0403", ATTRS{idProduct}=="6001", GROUP=="users", MODE="0660"
-   SUBSYSTEMS=="usb", ATTRS{idVendor}=="0403", ATTRS{idProduct}=="6014", GROUP=="users", MODE="0660"
+The following works for both a Raspberry Pi (Debian Wheezy) and Ubuntu 12.04,
+getting ordinary users (e.g. 'pi' on the RPi) access to the FTDI device without
+needing root permissions:
-Under other distributions, other group names are probably needed. On Ubuntu
-(12.04 here) I use the ``dialout`` group. Create a file
-``/etc/udev/rules.d/99-libftdi.rules`` containing::
+1. Create a file ``/etc/udev/rules.d/99-libftdi.rules``. You will need sudo
+   access to create this file.
+2. Put the following in the file::
-   SUBSYSTEMS=="usb", ATTRS{idVendor}=="0403", ATTRS{idProduct}=="6001", GROUP=="dialout", MODE="0660"
-   SUBSYSTEMS=="usb", ATTRS{idVendor}=="0403", ATTRS{idProduct}=="6014", GROUP=="dialout", MODE="0660"
+     SUBSYSTEMS=="usb", ATTRS{idVendor}=="0403", ATTRS{idProduct}=="6001", GROUP="dialout", MODE="0660"
+     SUBSYSTEMS=="usb", ATTRS{idVendor}=="0403", ATTRS{idProduct}=="6014", GROUP="dialout", MODE="0660"
-Some FTDI devices may use other USB PIDs. Use `lsusb` or similar to
-determine the exact values to use (or try checking `dmesg` output on
+Some FTDI devices may use other USB PIDs. You could try removing the match on
+`idProduct` altogether, just matching on the FTDI vendor ID. Or Use `lsusb` or
+similar to determine the exact values to use (or try checking `dmesg` output on
 device insertion / removal). ``udevadm monitor --environment`` is also helpful,
 but note that the environment 'keys' it gives are different to the attributes
-(filenames within /sys/devices/...) which the ATTRS will match. Perhaps ENV{}
+(filenames within /sys/devices/...) which the ATTRS will match.  Perhaps ENV{}
 matches work just as well, though I've only tried matching on ATTRS.
 Note that changed udev rules files will be picked up automatically by the udev
 See for more on writing udev rules.
+Arch Linux
+The `libftdi` package (sensibly enough) provides the `libftdi` library::
+    $ sudo pacman -S libftdi
+Similar udev rules to those above for Debian should be included (again in
+``/etc/udev/rules.d/99-libftdi.rules`` or similar), though the GROUP directive
+should be changed to set the group to 'users'::
+   SUBSYSTEMS=="usb", ATTRS{idVendor}=="0403", ATTRS{idProduct}=="6001", GROUP="users", MODE="0660"
+   SUBSYSTEMS=="usb", ATTRS{idVendor}=="0403", ATTRS{idProduct}=="6014", GROUP="users", MODE="0660"
 Testing installation