arduino-comm-example /

Filename Size Date modified Message
98 B
First draft of Arduino communication example.
90 B
Added tag 1.1 for changeset c334364e8be1
8.7 KB
Changed some file extensions, added documentation and a popup with info and license for the python user interface.
6.2 KB
Added a signal sent from the Arduino every 10 LED flashes. Also updated README file.
7.4 KB
Added a signal sent from the Arduino every 10 LED flashes. Also updated README file.
Arduino Communication Example
Copyright 2011 Christopher De Vries

Serial communication with the Arduino is relatively simple, but it can
sometimes be difficult to organize input and output around the other tasks you
want the Arduino to accomplish. I use a fairly simple framework for
two-way communication, but it relies on executing commands which are not going
to take a whole lot of time or add any delays to each loop.

The example includes the following files:

README.txt --- This file.

LICENSE.txt --- The license governing distribution and modification of this
                code. --- A graphical user interface written in python which uses
                 Tkinter. Note that this program requires that the pySerial
                 extension be installed. PySerial can be downloaded at

comm_example/comm_example.pde --- The example Arduino sketch. This program
                 Flashes an LED on for a second and off for a second, then
                 repeats. During this time it sends a signal over the serial
                 line indicating how many times the LED has been on, every 10
                 flashes. It also responds to inquiries about the current
                 state of the LED and the connection.

Basically every time the Arduino runs through loop I do two things:

1. Monitor and or change any I/O pins that require monitoring or changing.
2. Check for any input, if a full command is received, execute that command.

The framework assumes command sent and received by the Arduino will be text
terminated by a newline character. On the Arduino side the setup is fairly
simple. In the setup() function, serial communication should be initialized. I
tend to use 9600 bps if speed is not a factor, but it seems to work fine at
115200 bps as well. Use the following statement:


Next, I define a couple of functions. The first is the routine that reads
commands into the buffer and executes them when they are complete. This code
does not vary from program to program:

  void checkInput() {
    int inbyte;
    static char incomingBuffer[128];
    static char bufPosition=0;
    if(Serial.available()>0) {
      // Read only one character per call
      inbyte =;
      if(inbyte==10) {
        // Newline detected
        incomingBuffer[bufPosition]='\0'; // NULL terminate the string
        bufPosition=0; // Prepare for next command
        // Supply a separate routine for parsing the command. This will
        // vary depending on the task.
      else {
        if(bufPosition==128) {
          Serial.println("ERROR Command Overflow");

The code above reads one character into the buffer each loop (if the character
is available). If it comes to a newline character it terminates the buffer
with a NULL character and runs parseAndExecuteCommand(String command). The
buffer is limited to 128 characters. If too many characters are read into the
buffer, the Arduino responds with "ERROR Command Overflow".

The parseAndExecuteCommand function will change depending on the commands you
use. The one in my example responds to two basic commands:

1. If the computer issues CHECK, the Arduino responds with CONNECT, indicating
that it is ready and the connection is working.
2. If the computer issues QUERY, the Arduino responds with the state of the
LED (pin 13, HIGH or LOW). This routine will vary depending on the program.

  void parseAndExecuteCommand(String command) {
    if(command.equals(String("CHECK"))) {
      // Check connection, respond with CONNECT
    else if(command.equals(String("QUERY"))) {
      // Query state of the LED
      if(ledState==LOW) {
      else {
    else {
      // Unrecognized command
      Serial.println("ERROR Unrecognized Command");

The main loop is now simple. For any sketch you load on the Arduino, the
sequence will look like this:

  void loop() {
    // Do whatever monitoring and work is necessary each loop below
    <<Code goes here>>

    // Load and parse any commands

The example included with this README is a program that blinks the LED
attached to pin 13 on and off every 2 seconds (1 second on, 1 second off). If
it receives a query it will indicate the state of the LED.

I also include a python based user interface with which to interact with the
Arduino. The python side is a little more complex as I mix the event driven
style of a user interface with a threaded approach to I/O. A pair of threads
are created when the python program connects to the serial port (using
pySerial). The input thread assembles input from the Arduino until it receives
a newline and then places information in the input queue which is periodically
polled (every 100 ms) by the main event loop. The UI can then react to the
information received by the Arduino. Events in the UI can trigger commands to
go to the Arduino. These commands are placed in an output queue which the
output thread grabs and then sends down the serial line. 

In the example, the python user interface has a line at the top with a blank
where you need to put the name of the serial interface to the arduino. On my
Mac it is typically /dev/tty.usbmodemfd321, but you can look it up using the
Arduino IDE. Hit the connect button and in about 2 seconds you should receive
confirmation that the Arduino is connected. Next, just hit the query button
and the LED state at that instant should be indicated on the UI.

I hope this example helps you get started with 2-way communication with the

Note: The example code in this distribution is covered by the Artistic License
2.0, an open source license. This means you are free to modify and distribute
this code with some restrictions. Please read the LICENSE.txt file for more