App iOS v 2.0.5 - Disconnessione dell'app - "Bafang motor Basic write error, 82" - limite di velocità non funzionante - Nessuna differenza tra ROAD e OFFROAD
(ITA - segue traduzione in ENG) Motore Bafang BBS02B - controller 36v 25A (La versione dell'app iOS 2.0.5 non è presente tra i tag)
L'app iOS v 2.0.5 ora si connette al display e resta collegata (anche se si spegne lo schermo dell'iPhone) solo se si resta nella schermata che riproduce le informazioni del display, ma se si esce da questa schermata, ad esempio per modificare le impostazioni, e ci si dimentica di tornare alla schermata di default, l'app si disconnette dal display e bisogna chiudere e riavviare l'app per far ricollegare il display, perché neppure andando in "search device" e riavviando la ricerca il display non si riconnette. Quindi bisogna chiudere l'app completamente per far riconnettere il display.
Ho provato ad impostare il limite di velocità a 25 km/h nell'impostazione ROAD sia in "Display Setting" sia in "MotorPedal" modificando "Speed limit" (l'app restituisce il messaggio "Bafang motor Pedal write successfully,11"), ma il motore continua ad assistere anche oltre i 25 km/h. Ho provato a modificare le impostazioni MotorBASIC. Le modifiche sembra che vengano assegnate, ma quando do il comando "Write" l'app mi restituisce il messaggio "Bafang motor Basic write error, 82". Se esco dall'app, la riavvio e uso il comando "Read" la modifica risulta però applicata e riscontrata sul comportamento del motore.
Le impostazioni sono identiche tra ROAD e OFFROAD. Se cerco di modificare e differenziare le impostazioni tra ROAD e OFFROAD, le modifiche assegnate a uno dei due setting vengono applicate sia a ROAD che a OFFROAD.
(ENG) Bafang BBS02B engine - 36v 25A controller (The version of the iOS 2.0.5 app is not included in the tags)
The iOS v 2.0.5 app now connects to the display and stays connected (even if you turn off the iPhone screen) only if you stay on the screen that plays the information on the display, but if you exit this screen, for example to change the settings, and you forget to go back to the default screen, the app disconnects from the display and you have to close and restart the app to reconnect the display, because even going into "search device" and restarting the search the display does not reconnect. So you have to close the app completely to reconnect the display.
I tried setting the speed limit to 25 km / h in the ROAD setting both in "Display Setting" and in "MotorPedal" modifying "Speed limit" (the app returns the message "Bafang motor Pedal write successfully, 11") , but the engine continues to assist even over 25 km / h. I tried to change the MotorBASIC settings. The changes seem to be assigned, but when I give the command "Write" the app returns me the message "Bafang motor Basic write error, 82". If I exit the app, restart and use the "Read" command, the change is applied and found on the behavior of the engine.
The settings are the same between ROAD and OFFROAD. If I try to change and differentiate the settings between ROAD and OFFROAD, the changes assigned to one of the two settings are applied to both ROAD and OFFROAD.
Comments (6)
-
reporter -
- changed status to resolved
This has been resolved with firmware update eggrider_fw_v2_0_11.
The speed issue seems like a bafang error or wrong settings.
The dual Road/OffRoad profiles issue was already open, see reference: https://bitbucket.org/eggpower/eggriderv2/issues/1/road-offroad-profiles-are-not-saved
-
Thank you @Daiwer for raising the issues, but can you please next time raise every issue individually and not stack them in the same issue as it will be hard to track.
-
Also, please make sure you check all the issues before raising a new one https://bitbucket.org/eggpower/eggriderv2/issues.
The error 82, was already raised and it was fixed. https://bitbucket.org/eggpower/eggriderv2/issues/3/bafang-motor-basic-write-error
-
reporter Hai ragione, ma non riuscivo a vedere tutti i problemi sollevati, non so per quale ragione. Ora ho impostato la visualizzazione di tutti i problemi. Grazie ancora per il supporto.
-
- removed version
Removing version: EggRiderV2.0.3 - iOS (automated comment)
- Log in to comment
Intanto ho aggiornato il firmware del display alla versione fw 2.0.11 e ora non appare più il messaggio di errore nella schermata Motor Basic quando do il comando "Write".